AqueousPro™ Test Strip - 10 Pack
The AqueousPro™ test strips are used to test your water after your rainwater tanks have been sanitised with AqueousPro™ water sanitiser. Use the test strips to confirm that AqueousPro™ is within the required levels to ensure your water system has been effectively treated and sanitised to kill harmful bacteria and viruses. Not available for online purchase.
No online purchase — your local PWS franchisee supplies our products and provides expert advice and support, so you get the right solution for your water, not just a box in the post.
About this product
AqueousPro™ Water Quality Test Strips
Test your water quality with the AqueousPro™ Test Strips. A quick, simple solution to ensure your water storage systems are free of bacteria and viruses.
Single-dip test procedure to test for water quality in a broad range of concentrations. When using the AqueousPro™ Water Sanitiser, the AqueousPro™ Test Strips provide accurate results from 0.50 to 100 ppm (mg/L) in under one minute.
AqueousPro™ Test Strip instructions
To confirm AqueousPro™ water sanitiser has effectively passed through all your pipework and taps, the following instructions should be actioned when using the AqueousPro™ water quality test strips.
1. Open all internal and external water outlets (taps, showers, sinks, etc) and run for a few minutes to draw freshly sanitised water from the water tank, through your pump and into all pipework throughout the property. (Tap run times may vary depending on distance water travels from tank to tap.)
2. Dip one test strip into water sample for approximately 2 seconds and remove. Wait 30 seconds. Hold test strip next to the colour match chart and review results.
3. Ensure that colour concentration is between 10ppm and 25ppm to confirm sanitised water is present within your water supply network.
4. Allow adequate contact time. To confirm adequate contact time occurs to ensure the water sanitiser actively destroys bacteria and biofilm build-up in your water supply system, allow water containing sanitiser to sit in pipework for a minimum of 4 hours. Ideally up to 24 hours. Do not drink water during this period.
5. If test strip reads less than 5ppm after 24 hours, apply appropriate doses of AqueousPro™ and repeat test strip instructions.
Store AqueousPro™ water quality test strips in a cool (but not refrigerated), dark, dry place. Avoid touching test strips or exposing to sunlight and moisture. Remove only as many strips as are required and seal bag immediately. Use or dispose of correctly. Test strips can be disposed as normal trash waste.
Additional information
Additional information tab on page:
- Quantity: 5, 10, 50
Variant/option selector on page: Quantity — options 5, 10, 50.
Related products shown on page:
- Filter Housing Spanner — https://shop.pristinewatersystems.com.au/product/filter-housing-spanner/
- 40 Watt 4-Pin Ultraviolet Lamp Replacement — https://shop.pristinewatersystems.com.au/product/40-watt-4-pin-ultraviolet-lamp/
- 75 Watt 4-Pin Ultraviolet Lamp Replacement — https://shop.pristinewatersystems.com.au/product/75-watt-4-pin-ultraviolet-lamp/
Using AqueousPro™
Directions for use
- Best results are achieved when water is clean of organic material.
- Add the required quantity of AqueousPro™ to the tank according to the table.
- Use Test Strips after 24 hours to check effectiveness.
- Re-dose if required.
- Poor quality water supply may require higher dosage levels.
| Water Tank Size (L) | Dosage Rate |
|---|---|
| 50 L | 3.5 ml |
| 100 L | 7 ml |
| 250 L | 17.5 ml |
| 500 L | 35 ml |
| 1,000 L | 70 ml |
| 1,500 L | 105 ml |
Larger tanks: dose at 70 ml per 1,000 L — e.g. a 25,000 L rainwater tank takes 1.75 L.
Not to be taken. Keep out of reach of children.
Read safety directions before use.
Vented container — do not change cap. Keep upright at all times.
Active constituents: 7.9% Hydrogen Peroxide (7.9% w/v H₂O₂) with < 0.1% Silver.
Safety directions
AqueousPro™ is a concentrated product to be diluted in water. Use only as directed. Keep out of reach of children. Not to be taken undiluted. If swallowed, do not induce vomiting — seek immediate medical advice. Avoid contact with skin and eyes. If skin contact occurs, flush with water. If eye contact occurs, hold eyes open and flush with water for 15 minutes and seek medical advice if required.
Storage
Always store AqueousPro™ and AqueousPro™ test strips in a clean, cool, lockable and well-ventilated area.
Effectiveness
Use Test Strips to confirm effectiveness of AqueousPro™ sanitiser. Repeat the process until the water matches the colour zone from 5–15 ppm.